SpeedyBee F7 V3 50A 4in1 Stack

The SpeedyBee F7 stack with 50A 4in1 ESC is SpeedyBee's Flagship stack. It features a 50A 4in1 ESC and an F7 flight controller that supports the SpeedyBee phone app to configure your quad on the go. 

The SpeedyBee 50A 4in1 ESC supports upto 50A continuous output. The ESC runs BLHeli32 has a built in metal heatsink to help dissipate heat and includes a built in TVS protective diode designed to absorb voltage spikes when you plug in a battery or during a crash. There is also a very large 15000uF low ESR capacitor included. The ESC supports upto 128KHz PWM.

The SpeedyBee F7 V3 flight controller integrates bluetooth and wifi for easy changing of parameters and firmware via the SpeedyBee app. This new version includes an upgraded wireless module enabling 33% faster flashing and faster blackbox data download. The FC includes both solder pads and physical connectors enabling more rapid builds. The flight controller includes signal pads to enable upto 8 motor outputs, making it suitable for use with X8 cinelifters. An innovative 4x LED system on the side of the board provides basic "Lipo Checker" functionality giving a percentage indication of current battery capacity.

50A ESC Specifications:

- Product Name: SpeedyBee BL32 50A 4-in-1 ESC
- Firmware: SpeedyBee BL32 50A
- Continuous Current: 50A * 4
- Burst Current: 55A(5S)
- TVS Protective diode: Yes
- Heat Sink: Yes
- External Capacitor: 1500uF Low ESR Capacitor(In the package)
- ESC Protocol: DSHOT300/600
- Power Input: 3-6S LiPo
- Power Output: VBAT
- Current Sensor: Support (Scale=490 Offset=0)
- Mounting: 30.5 x 30.5mm( 4mm hole diameter)
- Dimension: 45.6(L) * 40(W) * 8.8mm(H)
- Weight: 19.2g with heat sink

F7 FC Specifications:

- Product Name: SpeedyBee F7 V3 Flight Controller
- MCU: STM32F722
- IMU(Gyro): BMI270
- USB Port Type: Type-C
- Barometer: BMP280
- OSD Chip: AT7456E chip
- BLE Bluetooth: Supported. Used for Flight Controller configuration
- Flash FC Firmware Wirelessly Supported. Please enter MENU > FC Firmware Flasher
- Download/Analyze Blackbox Supported.Please enter MENU > Blackbox Analyzer
- DJI Air Unit Connection Way Two ways supported: 6-pin connector or direct soldering.
- Flash(for BlackBox): 500MB
- BetaFlight Camera Control Pad Yes(CC pad on the front side)
- Power Input: 3S - 6S Lipo
- 5V Output: 10 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A.
- 9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A.
- 3.3V Output Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
- 4.5V Output Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
- ESC Signal Pads: M1 - M4 on bottom side and M5-M8 on front side.
- UART: 5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6)
- ESC Telemetry UART    R4(UART4)
- I2C: Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
- LED Pad: Used for WS2812 LED controlled by Betaflight firmware.
- Buzzer: BZ+ and BZ- pad used for 5V Buzzer
- BOOT Button: Supported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
- RSSI Input: Supported. Named as RS on the front side.
- SmartPort: Use any TX pad of UART for the SmartPort feature.
- Supported Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV
- Firmware Target Name: SPEEDYBEEF7V3
- Mounting: 30.5 x 30.5mm( 4mm hole diameter)
- Dimension: 41(L) x 38(W) x 8.1(H)mm
- Weight: 10.7g

Includes:

1x SpeedyBee F7 V3 50A 4in1 Stack
Accessories